How 2 , fixings on fibre glass bumper .

[K-Lone]

Find some suitable thin pieces of plastic .
http://img.photobucket.com/albums/v472/daddycav/DSCF4020.jpg

http://img.photobucket.com/albums/v472/daddycav/DSCF4021.jpg

Draw an outline to go by , I just drew round the top of the bumper .

http://img.photobucket.com/albums/v472/daddycav/DSCF4023.jpg

Cut your shape .

http://img.photobucket.com/albums/v472/daddycav/DSCF4024.jpg

http://img.photobucket.com/albums/v472/daddycav/DSCF4025.jpg
http://img.photobucket.com/albums/v472/daddycav/DSCF4026.jpg

http://img.photobucket.com/albums/v472/daddycav/DSCF4027.jpg

http://img.photobucket.com/albums/v472/daddycav/DSCF4028.jpg

http://img.photobucket.com/albums/v472/daddycav/DSCF4029.jpg

Put in place and draw a line when the bracket and lamp sit well .

http://img.photobucket.com/albums/v472/daddycav/DSCF4030.jpg

Messure and mark your holes , use holes on lamps .

http://img.photobucket.com/albums/v472/daddycav/DSCF4031.jpg

Make holes in plastic brackets .

http://img.photobucket.com/albums/v472/daddycav/DSCF4032.jpg
http://img.photobucket.com/albums/v472/daddycav/DSCF4033.jpg
http://img.photobucket.com/albums/v472/daddycav/DSCF4034.jpg

http://img.photobucket.com/albums/v472/daddycav/DSCF4035.jpg

Trial fit .

http://img.photobucket.com/albums/v472/daddycav/DSCF4036.jpg

http://img.photobucket.com/albums/v472/daddycav/DSCF4037.jpg

http://img.photobucket.com/albums/v472/daddycav/DSCF4043.jpg

Bond onto bumper , I used chemical metal .

http://img.photobucket.com/albums/v472/daddycav/DSCF4048.jpg
http://img.photobucket.com/albums/v472/daddycav/DSCF4049.jpg
http://img.photobucket.com/albums/v472/daddycav/DSCF4050.jpg

Side fixings , very easy , measure distance in from your old bumper and 20mm from the top .
You will need spacers , I used 2 suitable lock nuts , again chemical metal .

http://img.photobucket.com/albums/v472/daddycav/DSCF4051-1.jpg

http://img.photobucket.com/albums/v472/daddycav/DSCF4052-1.jpg

[K-Lone]

Did some side fixings on another bumper today , didn't think of it to start with so didn't take any pics from the beginning .

1) Measure 115mm from what I call the ridge ( where pre face headlights meet pre face indicator ) Then measure 22mm from the top ( sizes are to center )
You can measure from the car ( what I did 1st time )
Offer up the bumper and make a pencil mark where your hole is on car .

2) Lay a base for fixings , at least 5mm thick in the area you will be securing fixings you can use chemical metal or body filler ( I like chemical metal )

3) Use dome head screws and a big washer ( see pic )

4) drill a hole so that the dome head sits in it flush .

5) Use a small amount of chemical metal 1st just to hold it in place .

6) Check all measurements are right .

7) Now you can cover the washer with chemical metal too .

8) You should have good strong fixings .

http://img.photobucket.com/albums/v472/daddycav/DSCF4136.jpg

http://img.photobucket.com/albums/v472/daddycav/DSCF4138.jpg